| Customization: | Available |
|---|---|
| After-sales Service: | Support |
| Warranty: | One Year |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
High-strength HT300 one-piece structure casting iron bed, 30-degree step type flat rail structure, application of finite element analysis, excellent overall mechanical rigidity and stability, and can maintain long-term reliable accuracy, processing stability and tool life, stress relief treatment improve accuracy and stability, high-strength roller rail design, drive system adopts screw pre-tension design, improve response rigidity.
Both ends of the workpiece can be processed at the same time in one clamping, which greatly simplifies the manual operation, increases the output and reduces the process. The second spindle is capable of full turning and can express workpieces during machining, reducing cycle times.
1.Direct drive synchronous electric spindle device: magnetic ring type incremental encoder (Sine and cosine) positioning accuracy: 20 arc seconds, C-axis indexing accuracy: 40 arc seconds.
Effectively eliminate the vibration of spindle, and the deflection accuracy of the nose end is within 0.002mm. Improve the surface finish of the workpiece.
The rear-mounted rotor is used to facilitate installation and maintenance.
The spindle motor is equipped with cooling system to suppress the influence of thermal displacement and ensure a constant working temperature of the spindle. The spindle system has passed the strict dynamic balance test. It has good precision retention, high rigidity and high efficiency, so that the machine can not only complete finishing machining, but also rough machining and heavy cutting for users. It is especially suitable for mass production of complex shapes and high finishproduct.
2.High rigidity integral servo power turret. With rapid and precise tool change performance. The tool holder installation used high-rigidity BMT interface, and the power transmission shaft is driven by servo spindle motor.
3.The machine is equipped with THK linear guide rail and ball screw. The heat-treated and precision-ground ball screw can ensure the best precision and durability. Each axis adopts a direct transfer shaft structure and a double-anchor pre-relay method, which can minimize thermal displacement and greatly improve machining accuracy. High rigidity, large size, and heavy-duty linear slide rails can keep the accuracy of the machine unaffected when it is impacted, the displacement is smooth and the noise is low, which can prolong the service life.
4.Standard configuration FANUC system, and the feed drive adopts FANUC servo motor.
5.Perfect hydraulic and lubrication system, using high-quality hydraulic pumps, hydraulic valves and other components, greatly reducing the failure rate. The design of the hydraulic and lubrication system is simple and reliable.
6.Using Taiwan rotary chuck, oil cylinder and automatic chip removal device, which can greatly reduce the labor intensity of the operator and realize safe and efficient production. The above functional components can be controlled by programming. Special fixture.
| Name | Unit | SY150MS-II |
| The largest diameter rotating bed | mm | Ф380 |
| Max. processing diameter | mm | Ф100 |
| Max.Swing Over Cross Slide | mm | Ф160 |
| Max. processing length | mm | 150 |
| Spindle nose | / | A2-5 |
| Max. speed of spindle | rpm | 6000 |
| Hydraulic Cylinder/Chuck | / | 6" |
| Spindle hole diameter | mm | Ф56 |
| Bar diameter | mm | Ф45 |
| Spindle motor power | kw | 11 |
| Spindle motor torque | Nm | 61-125 |
| Spindle nose | / | A2-4 |
| Max. speed of spindle | rpm | 6000 |
| Hydraulic Cylinder/Chuck | / | 5" |
| Spindle hole diameter | mm | Ф46 |
| Bar diameter | mm | Ф32 |
| Spindle motor power | kw | 11 |
| Spindle motor power | Nm | 34-67 |
| X1/Z1 motor power | kw | 1.8/1.8 |
| X2/Z2 motor power | kw | 1.3/1.3 |
| X1/Z1 travel | mm | 135/370 |
| X2/Z2 travel | mm | 215/400 |
| Positioning accuracy | mm | ±0.005 |
| Repeat positioning accuracy | mm | ±0.003 |
| X/Z/S axis moving fast | mm/min | 30/30/30 |
| Slide rail type | mm | Roller 35/35 |
| Slide rail type | mm | Roller 30/30 |
| Turret type | pcs | BMT45-12T |
| Power motor | Kw | 4.0kw |
| Max. speed of | rpm | 5000 ER20 |
| The tool block specifications | mm | 20x20 |
| Circular cutter holder specification | mm | Ф32 |
| The adjacent tool change time | sec | 0.15 |
| Turret type | pcs | NC8T |
| Tool block specifications | mm | 25x25 |
| Circular cutter holder specification | mm | Ф32 |
| The adjacent tool change time | sec | 0.15 |
| Machine size | m | 2.2x2.1x1.7 |
| Machine Weight | kg | 3500 |
| Cutting fluid tank volume | L | 150 |
| Volume of hydraulic unit box | L | 40 |
| Hydraulic oil pump motor power | kw | 1.5 |
| Volume of lubricating oil tank | L | 2 |
| Auto lube pump motor power | W | 50 |
| Cooling water pump power | W | 750 |
Q1:How can l choose the most suitable machines ?
Please share your specifications with us, and we will help you select the best model. Alternatively, you can choose a specific model or send us the product drawings. We will ensure you get the most suitable machine.
Q2: What's your main products of your company?
We specialize in an extensive range of machinery, including CNC Lathe Machines, CNC Milling Machines, CNC Turning Machines, Vertical Machining Centers, Horizontal Machining Centers, and comprehensive turning and milling composite processing units.
Q3: Where is our factory located? How can l visit there?
Our five factories are strategically located in Guangzhou, Quzhou, Ningbo, and Guangdong. We wholeheartedly welcome you to visit us.
Q4. How do you transport it?
We provide comprehensive transportation solutions including DDP, CIF, FOB, and FCA.
Q5: What's the Payment Terms ?
Our payment terms are T/T: 30% initial payment upon order, with the remaining 70% due before shipment.
06: What's the MoQ?
A: The minimum order quantity is 1 set. (For some low-cost machines, the MoQ may be more than 1 set.)
We want to know:
1. We highly recommend providing us with the size and material of your workpiece for evaluation. If possible, send us the workpiece drawing so we can suggest the most suitable model.
2. If you require a CIF price, please kindly provide the port of destination.
){kind=link}